Facebook

Knowledge Base

Find your answer.

Support article

Bluey 500 Manual

 

Installation

  1. Mute your studio monitors.
  2. Power OFF the chassis.
  3. Inspect Bluey 500 and make sure nothing is surrounding the card edge connector.
  4. Carefully slide Bluey 500 into an empty slot in your power chassis.
  5. Make sure the module connectors sits well into the mating Edac chassis connector.
  6. Secure the Bluey 500 to the chassis using the four front-mounted screws.
  7. Power ON the power chassis.

Installation and setup


Using balanced XLR cables, connect the Bluey 500’s inputs and outputs from your 500-series chassis to your mixing bus or patch bay. If you are using two Bluey 500s in parallel (or stereo), connect the two units using an RCA cable between the front-mounted RCA jacks. Set all controls to full counter-clockwise position, and all pushbuttons deselected or in the off position. Set the Bypass button to the on position, and apply power.


Unmute the monitors, and verify that signal is passing to and from the unit. Set the INPUT, OUTPUT, ATTACK and RELEASE controls to about 12 o’clock, set COMP MIX to full clockwise, select RATIO 4, and press the Bypass button. Increase the INPUT until the meter is deflecting a few dB. Again, verify signal is passing through the unit. Done!

Controls


 

  1. Input: Sets the threshold and controls the level at which the compressor starts compressing
  2. Output: Applies makeup gain to compressed signal to compensate for signal lost during compression
  3. Attack: Controls the amount of time it takes for the unit to react to an incoming signal
  4. Release: Controls the speed at which the compressor releases the compressed signal
  5. Comp Mix: Allows the user to blend the dry uncompressed signal with the wet compressed signal to allow more natural sounding compression
  6. Ratio: Controls the amount of compression applied (Yes, it does all-buttons-in-mode)
  7. Meter Mode: Selector switches GR meters the amount of gain reduction applied  (+4 meters output level at 0 with +4dB output; +8 meters output level at 0 with +8dB output)
  8. RCA Stereo Link: Use standard 2-conductor RCA cable for stereo linking. 
  9. Bypass: Bypasses the compression circuit. 


Note: For proper performance, balanced XLR must be used for all inputs and outputs.

The Attack control

The Attack control on the Bluey 500 works a little differently than you may have encountered on other ‘76-style compressors. Turning the Attack knob to the left (counter-clockwise) will yield faster attack times; slower times result when turning to the right (clockwise). We’ve found this control scheme to be more intuitive; akin to a volume knob decreasing level to the left and increasing to the right.  

  • Attack: Continuously variable 20uS to 800uS
  • Release: Continuously variable 1200mS to 50mS 


Bluey 500's buffering:

Bluey 500 features additional input and output buffering circuitry not found on most other compressors; as such you may find the input to run a little hotter than you might initially expect. This extra gain is useful for directly inserting Bluey in a console insert point. Additionally, it serves to model the manner in which the original Bluey was used as a console insert while also ensuring stable level balance when adjusting the Comp Mix control.

Stereo linking

When running a pair of Bluey 500s via a stereo link, start by setting both units to matched settings, as the detector circuits are the linked elements - not the controls. Note that due to design limitations of the ‘76-style compressors,  no two units will ever be 100% matched without an external battery-powered balancing box. If you don’t have a balancing box, you may need to make slight alterations to the Input and Output controls to create perfect stereo matching.

All-buttons mode

By pressing in all four ratio buttons you activate what is referred to as “all buttons” mode. This “secret” mode changes the ratio to roughly 20:1. It also changes the bias of the circuit and the way that the controls interact with each other. The unit will become much more aggressive with its reaction knee becoming more like a plateau than a gentle curve and will have a more aggressive, dirty tone that sounds incredible on aggressive drums. The attack will become very punchy with a gooey “sucking” sound on the release.

Specifications


Attack    Continuously variable 800uS to 20uS
Release    Continuously variable 1200mS to 50mS
Ratio    Pushbutton selected 4:1, 8:1, 12:1, 20:1 and any combination
Voltage    ± 16v
Dimensions    Width:76 mm (3”)  
Height: 178 mm (5.25”) 
Depth: 229 mm (9”) 
Weight    1.47 kg (3.25 lbs)